Sawdust Girl®

Renovation, cabinet building and woodworking plans and tutorials. Build like a Girl®

Installing Raised Panel Wainscoting

All Posts, Remodeling 101

There’s nothing like raised panel wainscoting.  There are lots of other types of wainscoting, but if raised panel is the look you want, the only way to create it is with a LOT of woodworking skill and knowhow and a shaper or router table.  Even then, these giant panels would have been impossible for me to create on my router table.  They are just too big.  Sometime’s, even DIY’ers can get some help.Installing wainscoting

I knew I wanted full wall wainscot to to echo the lines in my bookcases so I built those first.  I built them out to the point where the faceframe was installed against the side walls so I could get accurate measurements as well as design my wainscoting.  This is the point that  I ordered from IntriG. (Sadly they are no longer in business.)  

Installing IntriG wainscoting

I drew up general plans with measurements and then Adam (my sales rep, nice guy) whipped up the real plans.  The best part?  They did all the math.  
I knew I wanted 3 panels high.  The bottom one medium height, the middle panel large and a small one on top.  His computer program took that info along with my measurements and put that into drawing so I could visualize exactly what it would look like on my walls.
I approved the sketches and then it was GO time!  Adam sent me some pics of how it goes down on the Wainscoting farm.  It’s all computerized in this technological world.
 
Full sheets of HDF (like MDF only High Density) are routed by a big machine.  When I’ve seen routered raised panels before, the corners are always rounded like you see in this picture.  That is what I DID NOT want.  But, IntriG has a super secret way of fixing that.

It’s super secret so I have no idea how –but the corners are sharp as a tack and look awesome!  They were sanded and primed and then shipped out.

And this is how it arrived on my doorstep.  Now the DIY comes back into play.

Installing IntriG wainscoting

The panels were very heavy so it would have been wise to wait for Wes to help me but I’m too impatient to wait and did it myself.  It would have been easier with two people, but I did it.
Installing IntriG wainscoting
I installed a filler 5″strip on the floor to sit my wainscot on top of because I wanted them as tall as possible.  I made sure to point that out in my design when I ordered.  My baseboards only cover 1/4″ of my wainscot that way.
 I made sure the filler strip was level so all my panels would also be level  I marked my studs on the ceiling and the filler strip so I’d know where to nail.  Other than the weight factor, installation was easy!  All I had to do was glue the tongue and groove seams and nail the panels in place.   I used a wood block and mallet to tap the panels together to get tight seams.
One thing I did wrong:  I applied glue to a seam and then tried to put the next panel up and realized there was an outlet there.  I had to measure, mark and cut that hole and by the time I installed the panel the glue had start to harden so I didn’t get a really tight seam.  It wasn’t too bad but I had to use some extra Bondo there.
The panels were all labeled and numbered so I knew where to start and which panel went where.  I only had to trim a little bit off the end panels because IntriG sends those panels a little extra wide in case your measurements weren’t quite perfect or in case your walls aren’t plumb.  
I had to cut out several outlet holes and the wainscoting is 5/8″ thick, so I installed these extenders — which come with screws that reach the junction box.  Nice, neat, clean.  Just the way I like it.
Installing IntriG wainscoting
A couple outlets were right on my routed profile but IntriG thought of everything.  My order came with a reverse profile strip that fits inside the panels.  
Installing IntriG wainscoting
You cut off what you need and glue it in where you need it.

Installing IntriG wainscoting

All primed and painted.

The window was a bit tricky.  The fact that I did full wall wainscot added to that.  I had to measure and cut a U out of two panels.  I had some gaps here but just filled it with Bondo and they completely disappeared.

I wasn’t satisfied with the window at this point.  My window trim was exactly the same width as the wainscot so it didn’t look like I had any window casing.

Also, the part of wainscot above the window was too narrow to have a routed panel so it was just plain and I thought it looked odd.

Trimming out Library window

So I trimmed the outside of my existing window casing with a thin little strip of moulding to make it look like a chunky window casing.  I also added a jury rigged crown piece at the top that I created using like 5 different strips of wood and moulding.  It was a hot mess while I created it but it looks good in the end.  

Trimming out Library window

And that is how I installed the wainscoting in the library.

DIY Library with White Built-ins and Wainscoting
Installing IntriG wainscoting

·

Comments

  1. We love a raised paneled wainscoting at our house. We did the faux flat paneled ones at our house and it hurt my carpenter husbands heart. When we are in our next house these will be on the walls! It’s beautiful!

  6. That’s still lots of work! You did an awesome job! Love what you did with window esp the crown part. So much nicer!

  12. Hello,
    I absolutely love your wainscoting! It looks so professional. Can you give an estimate of how much it would have cost? Thank you!
    Mary

  15. OMGosh! I’ve never commented on any blogs before, but this is just FABULOUS!!! You have so much motivation and TALENT! It looks gorgeous!

Legal Stuff

Terms of Use

Privacy Policy

Disclosure

Recent Posts

Disclaimer:

Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.